Anycubic Mega S Firmware Update

Posted on  by admin

With this, I want to sum up all basic upgrades, mods, some suggestions and more. I have made a little test print you can try to print. You can download it HERE. some basics, mods and upgrades for the bed. some suggestions for the hotend (cover, silent fan, better cooling). new spool holder and better management of the filament. some design advancements .

Basics

vibration dampers. making the printer completely silent (fans, new motor drives). some useful tips for a firmware upgrade. You can find everything about Slicer Here. So first, everything you really need, or which is easy to do.

The Ultrabase is the best bed, I ever have used. But it must be clean! So please keep it clean! Before every print, I would suggest, that you clean it. Just take some isopropanoland give it a wipe with a towel. You can also use nail polish remover as long as it is NOT ACETON!

Then, you really must level the bed perfectly. Do it as long, as it is perfect (at least for you). I really had problems with my front right corner, because when I loosen it, the rear left goes down and vice versa. Also, my bed is also not perfectly flat, but it works. You maybe have to change the screw wich hits the end stops.

One more thing for the bed, a little bed handle so you don’t burn your fingers:You can use this or this.

Overall

With this you can tension your printbed belt: Y-Tensioner. The bed has no isolation, further a lot of heat is lost and the heating takes longer.

Therefore, you can install aisolation. So first, I made a new Cover with bigger (Honeycomb Style) holes, for a better airflow: Hotend Cover. For this cover, I would recommend that you change the right fan for a silent one like the Noctua NF A4x10.

The left turbo fan is quite good. Altough it is very loud, I would keep it.​. There are several designs for fan ducts. I would say they really help, and I also use one. A really big advantage is, that they provide cooling from both sides. I use this Part Cooling Fan Duct.

This is just a little cover for the cables, doesn’t do much, but it protects the cables. When you print high objects, the cable may get squeezed at the top. To prevent this, you can use a cable guide.

For this, you must cut the old cable ties and put new cable ties on it. You could also use this little Cover. Or you print a Cable chain. Buy whatever Filament you like. The most are even from the same manufacturer, but with another brand name on it.

I can recommend: Amazon Basic, Eryone, Geetech, 3D Jake …. (You don´t need this for the new Anycubic S Pro (Mega S). Basically, the original filament spool holder is crap.

I remixed one from philwild. Mine fits perfectly together with the thing I will talk about next. This is my filament spool holder: Filament Spool Holder. (You don´t need this for the new Anycubic S Pro (Mega S). I really had some Problems with the original magnetic ball thing.

Firmware

It always fell off, then I tried some other holder which leaded to filament breaking. So I designed my own. With this holder, the Motor is mounted at an angle, so the filament doesn’t bend as much. Furthermore, the angle to the Spool holder is much better.

This is my Sensor Holder: Sensor Holder. However, you can also just disconnect the sensor. This is just a nice tool rig. You can put all your tools in. Nothing more to add. And a holder for your caliper:. This will really let your printer be the best out of all. It’s just for aesthetics. So I want to list here 2 different Face Plates.

On my printer, I use this one:FacePlate. The white under this plate is just paper or any other material.

List of Spare Parts

Can be any color. The other one:FacePlate. The printer can sometimes vibrate very much. The simple way: Just put some foam (when you order something, you will get some for sure) under the feet.

It will help some, but not for long. But I still use it (I just order enough). Nevertheless, you can print this: Squash Feet. These ones are not as high. (with my guide, you don’t need to mount the power supply fan outside, so the printer doesn’t need so much space beneath it.). For this vibration dampers you need 4x Squash Balls. Ok, so there are basically 2 variations.

Lightning on the hotend, or lightning on the housing.

Filament

A ring lightning which directly lights the printed part:Ring LED Holder. A compatible led would be thisLED Ring 80mm. If you also have the fan duct installed, you need to print this one: ​Ring LED Holder 100mm.

Furthermore you´ll need to buy the bigger LEDRing100mm. Or you just glue some led´s into the cover. You need some 12V LED. To install any leds, just connect it to the right fan cables.

A led stripe around the printer. To mount it print this: LED Mount. And a led strip. You can cut the strip and just connect it to the powersupply. Ok, so you have done all above, but want your printer to be even better? What about that loud sound’s you printer does? Do you have some Z wobbling? OK, then make your Anycubic silent.

At this step, you have to open the bottom plate of the printer. Please turn the power off and unplug the cable! One of the loudest fans on this printer is the PSU fan. I got inspired from some other designs, and designed my own PSU cover. On the one side, the power supply gets much more air, on the other side, it is much quieter with it.

You can find my blog post about it here:. Ok, next on the list is the fan next to the power supply.

​For this, I would recommend printing this fan duct: Fan Duct. Again, you also need a new, not as noisy fan. You need a 40mm x 10mm fan. For fan installation, use the included orange plastic things to tighten them to the cover or fanduct. They reduce the vibrations a lot. When all your fans are quiet, there is still one sound. It’s a very high-pitched annoying sound. But first check, if you even can swap your driver.

Thank you!

On some, they are soldered on. It depends when and where you bought the printer. For this, you have to open your printer. The drivers are the small black boards with the silver heatsink on it. On the one, you can see that you can take it of and swap them. You can also see the black plastic mount below. So if you have the swappable drivers you can go on.

The 32bit Trigorilla board has soldered drivers. They are directly on the big board. When it looks like the picture above, you can´t swap your drivers (At least not without soldering).

If you have this board you could buy a new 16 bit Trigorilla board. You will need 5x TMC 2208: (for: X, Y, Z, E0 (Extruder), E1 (second Z). There are some different versions on the market.

Silent Printer

If you can find some, which are called V2.0 you just can swap then out.

  • Also, when you get them, check again if they are really V2.0.
  • If you don´t find any, or got delivered others, you have to flash a new firmware.
  • Be sure, to then take the right hex file (Marlin-AI3M-vx.x.x-TMC2208.hex).

You can find more to this under the section Firmware. I recommend these TMC2208. Look at the marks on the board and on the driver, don´t put it in in the false direction.

  • When you install it, you must also check the voltage and probably change it.
  • For this you will need a mutlimeter. There is no universal Vref.
  • Its different for everyone. You will need to test it for your printer.
  • But at least, stay between 0,8 and 1,4 V. ​X driver = 1,15V. E0 (Extruder) = 1,25V .
  • E1 (second Z) = 1,15V. You can measure the voltage on the upper right hole (or on the screw, but you must turn this to change the voltage) on the driver and on the Ground GND.
  • Now just put the fan duct back on. Now just test all axis. They should all work.
  • If not, open the printer again, and check if any driver is very hot (nearly burn your fingers). If yes, this driver is maybe broken.
  • If no one is too hot, check the voltage again. Than check the cables if every is plugged in correctly.
  • If it still don´t work just comment.
  • Also test printing a part. When you get shifting layers or under extrusion, you have to increase the voltage a bit (in 0,05V or 0,1V steps).
  • Maybe you have noticed it, maybe not. But the clutches for the Z-Axis are very stiff. Therefore I changed them with better coulings.
  • These ones are much more flexible and will eliminate any Z-Wobbling. But the installation is kinda pain.

You must unscrew the motors from the top, and then put the clutch out.

Hot End

When you have the opportunity, you should take the screw drive out, and clean it (You will never do it again). After cleaning, put a some oil or lubricant on it again. Personally, I didn´t install it. But there is a slight chance, that the motherboard could get to hot on very long prints. Furthermore, it could than be destroyed.