The Generac PWRcell home battery and inverter. The Generac PWRcell (pronounced “power cell”) is a whole-home solar battery backup system from a trusted American company long-known for its backup generators.
It all started in 2019 when Generac bought Pika Energy, the original developer of the PWRcell, and Neurio, a manufacturer of home energy monitoring equipment.
By combining the technology from the acquired companies with know-how from over 60 years of making generators, Generac began marketing PWRcell to compete with the likes of the Tesla Powerwall and LG Chem’s RESU home batteries.
So how does the PWRcell stack up? Below is our complete expert review of the PWRcell ecosystem of products, with an analysis of specs and comparisons to other top batteries.
But first, here are some important facts about PWRcell:. Each battery cabinet can store between 9 and 18 kWh of energy using between three and six 3 kWh battery modules.
Two battery cabinets can be combined for up to 36 kWh of storage. PWRcell can deliver up to 12,000 watts of surge power to start heavy-duty appliances like well pumps and air conditioners.
When used with Generac’s Smart Management Modules, the PWRcell system can prioritize the startup of large appliances, allowing it to run more devices than any other solar battery system on the market.
The Generac PWRcell system can only be installed alongside a new solar system, and adds between $11,000 and $18,000 to the cost, depending on the size of your system and where you live.
Additional 3 kWh modules can be purchased for around $2,000 and installed in the battery cabinet to add storage capacity as needs change.
- Generac will debut a backup generator in 2022 that will provide additional flexibility in off-grid situations by charging the PWRcell battery if it gets low when the sun isn’t shining.
- Instead, it is an integrated system of components that work together to make the energy storage system more effective and efficient.
- Generac makes every piece of equipment for a home solar system, except for the solar panels and racking.
Cost and availability
How PWRcell compares to other top home batteries
A PWRcell system includes the following main components:. SnapRS inline disconnect switches that go between each solar panel and allow for rapid shutdown in case firefighters need to work on the roof.
PV Link substring power optimizers that take energy from the panels and send it to the battery and inverter. PWRcell battery modules to store solar energy, inside a specially-designed battery cabinet.
A PWRcell solar islanding inverter that connects everything together and sends power to the electrical panel in your home.
On this page
Generac’s PWRview monitoring app
- Here’s how they all fit together:. The main components of the Generac PWRcell system.
- Image source: Generac. Now let’s look at each of these components.
- These are fairly straightforward pieces of hardware that have an important job in the PWRcell system.
- The SnapRS switches connect between each solar module in an array and will shut down the output of that module within 10 seconds from whenever the inverter is turned off.
- Rapid shutdown is a fire code requirement of solar systems, and these switches are how Generac accomplishes this task.
- The PV Link boxes are substring power optimizers.
- They attach between a short string of solar panels (up to 2500 W) and the inverter, and ensure that the DC power delivered by the panels gets sent to the inverter as soon as panel output reaches 60 volts.
- The PV Link was initially developed by Pika Energy to integrate with the PWRcell battery.
- Because they optimize the power output of a string of panels, the PV Links are somewhat less efficient than microinverters and DC power optimizers, which are attached under each solar panel in an array.
- The advantage of the PV Link is having fewer points of failure, at the expense of a little less energy output over time.
- For people who want the extra juice, Generac has announced its own microinverters, which will be available later in 2022 (more on these below).
About Generac Power Systems
- The PWRcell battery cabinet can hold up to 6 modules, each of which can store 3 kWh of usable electricity.
- The cabinet can be set up with 3, 4, 5, or 6 modules, allowing 9 - 18 kWh of storage.
- Here’s how that looks:. Generac’s modular battery cabinet design allows for future capacity expansion.
- Image source: Generac. The battery is charged using DC power sent directly from the solar panels. This makes the battery very efficient compared to batteries like the Tesla Powerwall and sonnenCore, which charge using energy that gets converted from DC to AC and back again, causing some loss of energy in the process.
- The downside of this DC-coupled design is that PWRcell batteries cannot be added to an existing home solar system without rewiring everything at great expense.
- The PWRcell is meant for new solar installations only, and actually, the battery itself is optional.
- If you think you may want Generac battery backup in the future, you can get a solar system installed that includes the SnapRS, PV Link, and PWRcell inverter, and add the battery cabinet at a later time.
The future of Generac’s PWRcell
Learn more: Is a DC or AC battery right for your home? The Generac PWRcell inverter was designed to operate a home in grid-connected or “islanding” mode in case the grid is down.
It can be set by the homeowner to one of several modes, including backup power, self-supply, time-of-use, and zero-export. The inverter comes in two models: . X7602, which can provide up to 7,600 W of single-phase AC power when connected to the grid.
X11402, which can provide up to 11,400 W of 3-phase AC power when connected to the grid. Most homeowners will end up with the X7602, while commercial businesses are the target customer for the X11402.
Both inverters can accept up to 30 A @ 420 VDC from solar panels, and both output 9,000 W continuously in islanding mode when connected to one 18-kWh PWRcell battery.
Both inverters can deliver up to 12,000 W to start a motor. That’s a very impressive number, as it means a PWRcell inverter can start a well pump, sump pump, or a 3-ton HVAC unit.
Compared to Tesla Powerwall’s max peak output of 7,000 W, the PWRcell is much better. In addition to the required components, Generac also makes some optional pieces of equipment to provide extra flexibility.
- Automatic transfer switch (ATS).
- Smart Management Modules (SMMs).
- Sure-Start HVAC soft start box.
- This is where the PWRcell system really eclipses other home energy storage solutions.
- Generac brought these components from their home generator business to complement the PWRcell battery.
- The ATS and SMMs automatically shut certain appliances down, based on priority, to start up other appliances that require high surge power.
- Using these components, homeowners can run nearly their entire home on a single backup battery in the event of a grid outage—something many other companies’ batteries can’t provide.
- Altogether, this makes the Generac PWRcell one of the most exciting home batteries on the market.
- These specialized pieces of equipment are meant to control multiple HVAC units.
- Using a Generac ATS can allow one PWRcell inverter to manage up to 4 individual HVAC units, turning them on and off so they don’t overload the inverter’s capacity by starting all at once.
- Generac SMMs are small boxes that contain hardware to turn a given circuit off and on, based on how much of a priority it is to keep powered.
- They are installed in-line, which means they need no external power or communication—the circuits are turned on or off via a powerline signal from the PWRcell inverter.
- Basically, when the appliance wants to start, the SMM tells the inverter to check whether it can.
- If a higher-priority appliance is running, the SMM will not allow its appliance to start up.
Bottom line: Is the Generac PWRcell system right for you?
When the higher-priority device is no longer running, the SMM allows the lower-priority device to start. This way, the home’s appliances can all run off the same inverter and not overload the circuit by all drawing power at once.
This piece of equipment is used to reduce the start-up current that an air conditioner compressor needs.
It further reduces the peak power consumption needed and allows the PWRcell system to keep running essential equipment as an air conditioner starts. Here’s a look at how SMMs and a Sure-Start box work within the PWRcell system:.
Image source: Generac. The image above shows how the PWRcell can power three of the most important appliances in the home as it operates in a grid-down situation.
Here’s what’s happening, from bottom to top right in the image:. The sump pump is wired without an SMM so it will always receive power when it needs it.
The well pump is set to Priority 1 using an SMM to turn it on whenever it needs to run to supply water to the home. The 3-ton A/C is set to Priority 2 and allowed to run when the well pump is not running.
A Sure-Start box is attached to keep the current it draws from overwhelming the inverter. The 5-ton A/C is set to “lockout” using an SMM, which means it will not turn on when the grid is down, because it would draw more power than the PWRcell inverter can provide.
Another optional addition to your PWRcell system is Generac’s PWRview monitoring app.
- It’s a one-stop-shop for information about energy generation and usage in your house.
- The app contains data on solar generation, battery charge, grid usage, and more - and can even give you an estimate of your next utility bill based on that data it’s collected if you enter your rate plan.
- It certainly sounds like a good app to have, and its functionality is similar to other solar monitoring solutions from equipment manufacturers and solar installers.
- Unfortunately, reviews of Generac’s Android and iOS apps are not positive.
- Users complain about glitches, missing data, bad customer service, and more.
- This seems to be one area where Generac has stumbled, in regards to its PWRcell system.
More reading on EnergySage
- If you’re curious about how the app works, check out the below video about its features.
- Generac’s PWRcell components are sold through a nationwide network of licensed dealers, so pricing can vary, depending on the area where you live.
- That said, we do have some pricing information.
- Generac has said that a minimum-size 9 kWh PWRcell system will cost about $10,000, plus installation costs, which we estimate will be between $1,000 to $2,000 more than a solar installation without a PWRcell.
- Each battery module can be purchased separately for $1,900 - $2,000, so the cost of a full-sized 18 kWh PWRcell system ranges from about $16,000 to $18,000 installed, depending on offers from dealers in your area.
SnapRS switches and PV Link optimizers
- The good news is that the PWRcell is eligible for solar storage incentives in certain areas.
- Not only that, when you install a solar system, you can claim the 26% federal solar tax credit.
Can you go off-grid with the Generac PWRcell?
These incentives (as well as other applicable incentives and rebates you may qualify for) can reduce the cost of a solar-plus-battery storage system substantially.
Generac is a solid, reputable company that stands by its products. You can count on it to be around for decades to come. While that’s a good basis for trusting a warranty, the numbers need to be right.
Where to buy the Generac PWRcell
Let’s see how well they fare when it comes to offering their customers protection against product failures. The good news is, the Generac PWRcell warranty covers parts, labor, and limited travel (100 miles/3 hrs maximum, per occurrence) for all components of the PWRcell system.
The length of coverage depends on the product type and Generac promises the products will be free from defects in material and workmanship during their coverage period.
- Here’s a look at how long each component is covered:.
Generac PWRcell warranties
Importantly, the pieces that are going to stay up on your roof for 25 years (PV Link and SnapRS) are warrantied for 25 years.
Key things to know about the Generac PWRcell
The PWRcell inverter and battery come with 10-year warranties, which is fairly standard in the industry for these components.
Additionally, the throughput warranty for the battery modules is fairly standard. To put it in perspective, if you drained each battery module 100% of its usable power (3 kWh) every day, you’d get to 7.56 MWh in about 6.9 years.
How does the Generac PWRcell work?
The vast majority of people will choose to retain some battery capacity for emergencies, and therefore, will use less.
To get to the full 10 years, don’t go over an average of 69% drain per day. Unfortunately, the PWRcell battery module warranty doesn’t say anything about how much capacity the modules will retain over those 10 years; only that they will be free of defects in materials and workmanship.
Can you go off-grid with Generac PWRcell?
If you think the batteries have lost more capacity than they should, it’s up to you to convince Generac of that, and up to them to agree with you.
This isn’t normal. Many other batteries on the market, including the Tesla Powerwall and its main competitors, guarantee between 60% and 70% of the original capacity at the end of their warranty periods.
This is an oversight for Generac. We’ll update this article if that changes. Going off-grid with solar is not for the faint of heart. In general, you need to oversize your solar system and battery capacity to generate and store enough electricity to get through 2-3 days with little to no sun, something you very well may experience - especially in the wintertime.
Despite that, when it comes down to it, the Generac PWRcell is better-suited for an off-grid lifestyle than most other solar batteries.
PWRcell warranty information
The modular battery can be hooked up with as little as 9 kWh of storage capacity or as much as 36 kWh in two cabinets.
Using Generac’s SMMs and ATS as described above can allow you to run a good deal of home appliances off of one or two PWRcell inverters.
- That said, unless you spend a lot of money to oversize your solar system, you’re going to need some form of backup generator.
How much does the Generac PWRcell cost?
Many off-gridders turn to a fossil fuel generator on winter days when their solar systems aren’t producing enough and their batteries are low on energy. The PWRcell system does not currently interface with Generac’s line of backup generators, but the company recently announced a new product they’re calling PWRgenerator.
It’s a 9 kW backup generator designed to interface with the PWRcell system that runs on either natural gas or liquid propane. The Generac PWRgenerator, coming in late 2022.
When the PWRgenerator becomes available, it will work by acting as a backup to your backup. The system will detect whenever the PWRcell battery discharges to 30%, then turn on PWRgenerator to recharge the battery to full.
Generac says the generator can charge the 12-kW battery from 30% to full in about an hour.
The generator is scheduled to be available sometime in early 2022, but there is no word on the price yet.